Fibre Optic Cable Management

Fibre Strain Relief Boots are effortless to install as they can be inserted without the use of any tools whilst still providing protection to wire and fibre against rough panel hole edges.

Ferrule Dust Caps provide environmental protection for 2.5mm ferrules. The flexible TPE material is Ro. HS compliant, durable, and provides a snug fit.

Fibre bend accessories can be used in combination with our fibre protection range.

Optical Fibre Bend Limiting Tubing offers the ultimate protection to fibres eliminating problems such as crushing, kinking and micro bending whilst supplying an entire self-managing solution to managing the routing of fibre

These Optical Fibre Manifold enables small multiple fibre cables with aramid to be mechanically and securely terminated. The manifold is stackable and provides breakout for up to 4 wires. A development kit is also available that contains all adapters, OFM-4-05-19BLK.

Push-fit barbed cross fittings for connecting four tubes together.

These OFBLT zip tools are used to install fibre into the OFBLTS slit tubing. The fibre is slid into the side of the tool. This is followed by the slit tubing being fed over the horn of the tool. The tool is then slid into the slit tubing, thus installing the fibre.

The optical Fibre spool is made of two extruded clips that snap into each other to form a clip with a smooth, curved surface to accommodate fibre optic bundles.

The range of Fibre Management products supports rack brackets which mount into a 19 inch rack with a quarter turn. These can be used to run optical fibre alongside a racking unit.

Fibre Cut-out Adapters convert a hole cut-out for an SC connector into a hole cut-out for an ST connector. The Optical Fibre Duplexer enables cable with aramid strands to be broken out and mechanically terminated.

The Fibre Management range supports many low profile fibre reels for spooling excess fibre onto a PCB board. Some reels can be broken apart to form a controlled bend around a 90 or 180 degree turn. The range also offers stacking pillars and stand-offs which can be used to stack multiple reels for compact spooling of multiple runs of fibre. Fibre Guides are used to assist with reeling and corner guides maintain a bending radius through a 90 degree turn.

This is 900 µm PTFE Tubing that comes in a 120 meter coil. It is designed to prtect fiber in the Opticle Fibre Flat manifold.

The Fibre Management range provides Fibre Boots which provide strain relief for Micron Fibres. They provide added protection to the fibre while routing through a hole

The Fibre Management range supports many low profile fibre reels for spooling excess fibre onto a PCB board. Some reels can be broken apart to form a controlled bend around a 90 or 180 degree turn.

Optical Fibre & Ribbon Fibre Splice Protectors offer added protection in fibre management applications. There are two types available. Both consist of inner and outer tubing's and type 1 includes a stainless steel rod whereas type 2 uses a ceramic rod. They offer high protection for fibre

Fibre Splice Trays & Protectors are ideal for eliminating the potential hazard of macro and micro bends which can occur during the mishandling of optical fibres. The trays are stackable to any number and inter-tray fibre routing is possible. They can be used with splice holders, splice protectors and bend limiting tubing. Also available as a kit.

Fibre Splice Trays & Protectors are ideal for eliminating the potential hazard of macro and micro bends which can occur during the mishandling of optical fibres. The trays are stackable to any number and inter-tray fibre routing is possible. They can be used with splice holders, splice protectors and bend limiting tubing. The lids, trays and hinges are all sold separately or in a kit: OFST-A-P-1

Fibre Strain relief glands provide added protection to jacketed and bare fibre while routed through holes.

Optical fibre bend limiting clips, available in three different types to provide protection from breaks and kinks in any application.

Dust Caps provide environmental protection for SMA, ST, and FC connector adapters. The flexible PVC material is durable and provides a snug fit.

Fibre Dust Caps and Dust Caps with Metal Chain prevent unwanted foreign bodies and dirt getting into fibres and wires.

These fibre splice holders come in a variety of slot and mounting method configurations and can hold up to 24 splice connections.